Plumbing Basics: Your Key to Installing a Bathtub
Plumbing Basics: Your Key to Installing a Bathtub
Blog Article
How do you actually feel about How to Install a Bathtub Yourself?
Installing a bath tub isn't precisely rocket science, however it does call for solid plumbing, woodworking, as well as sometimes, tiling skills. Replacing an old bathtub with a brand-new one is likewise a reasonably tough project. If the old bathtub is readily obtainable, the project can move quickly; if you need to open up a wall to eliminate the old bathtub and also position the new bath tub, the task is much harder. In either instance, the job is within a home handyman's skills, although you will require an assistant to leave the old bathtub and also embeded in the brand-new one. Ensure you have certified yourself for the work as well as fit attempting it. Rather than employing a specialist to take over a halfway-completed project, it is much better to take into consideration utilizing one before you start. Possibilities are you might require a specialist plumber to make tube links.
This short article will certainly help you mount a brand-new bath tub in your shower room if you have actually currently gotten a new bathtub and also do not need to alter the arrangement of your previous water system pipes.
Your devices as well as material checklist ought to make up the following:
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installment, then the first thing you must do is separate the water system. After doing so, activate the taps to drain pipes any water continuing to be in the system. The procedure of removing the existing faucets can be quite bothersome because of the restricted gain access to that is usually the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the taps. Have a cloth ready for the staying water that will certainly come from the pipes. Once the supply pipelines have been gotten rid of, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary taps from turning throughout this procedure. When the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleansed of any type of old sealing substance.
Prior to carrying on to fit the new faucets, contrast the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will need a plastic port to stop damage to the thread. One end of the connector fits on the plastic tail of the faucet and the various other end gives a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will call for reducing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the faucet in the installing hole in the bath/basin guaranteeing that the washers remain in place in between the tap and also the sink. Safeguard the faucet in place with the producer provided backnut. Once the tap is safely in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with regular tap connectors. The previous kind should be linked to the faucet finishes initially, tightening up just by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Setting up the Bathtub
Utilizing both wood boards under its feet, position the bathtub in the required setting. The wooden boards are valuable in uniformly spreading out the weight of the bathtub over the area of the boards instead of focusing all the weight onto four little points.
The next goal is to make sure that the bathtub is leveled all round. This can be accomplished by checking the level as well as adjusting the feet on the bath tub till the spirit level checks out level.
To install taps, fit the bottom of the furthest versatile faucet connector to the suitable supply pipeline by making a compression sign up with; then do the same for the various other tap.
Activate the supply of water and check all joints as well as new pipework for leaks and also tighten them if essential. Fill up the bath tub and additionally examine the overflow electrical outlet and the normal electrical outlet for leakages.
Finally, repair the bath paneling as described in the manufacturer's user's manual. Tiling as well as sealing around the tub ought to wait till the bath tub has been made use of a minimum of once as this will certainly settle it right into its final position.
Planning for the Setup
First of all, the sustaining framework provided with the bath should be fitted (if called for) according to the producer's instructions. Next off, fit the taps or mixer to the bath tub. When suitable the tap block, it is important to make sure that if the tap features a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bathroom, it is additionally practical to fit a supporting plate under the taps unit to stop stress on the tub.
Fit the flexible faucet adapters to the bottom of both faucets utilizing 2 nuts as well as olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet via the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you make use of all of the supplied washers.
Attach the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath ought to currently be ready to be fitted in its final position.
Tiling Around the Bathtub
In the area where the bath satisfies the tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the installation can relocate enough to crack a stiff seal, causing the water to permeate the wall surface in between the bath as well as the tiling, bring about difficulties with dampness as well as feasible leaks to the ceiling below.
You can pick from a selection of coloured sealers to assimilate your fixtures as well as installations. They are sold in tubes as well as cartridges, and also are capable of sealing voids approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of soaked newspaper or soft rope. Bear in mind to constantly fill the bathtub with water before sealing, to allow for the activity experienced when the bathtub is in use. The sealer can split fairly very early if you do not take into consideration this movement prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also quickly readily available on the market. It is a good idea to fit the ceramic tiles making use of waterproof or water-proof glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a devoted reader about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I assumed sharing that editorial was mandatory. So long as you liked our blog entry please remember to pass it around. Thank you for your time. Kindly come by our website back soon.
Navigate plumbing issues professionally. Report this page